x 

Feather HUZZAH avec ESP-F V1.1 WiFi

z8019_01
z8019_02
z8019_03
Fournisseurs Adafruit
Référence:  z8019
Disponibilité du produit:   In stock
Prix ​​de vente21,50 CHF

Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores.

This is the Adafruit Feather HUZZAH ESP-F V1.1 - our take on an 'all-in-one' ESP-F V1.1 WiFi development board with built in USB and battery charging. Its an ESP-F V1.1 WiFi module with all the extras you need, ready to rock!

At the Feather HUZZAH's heart is an ESP-F V1.1 WiFi microcontroller clocked at 80 MHz and at 3.3V logic. This microcontroller contains a Tensilica chip core as well as a full WiFi stack. You can program the microcontroller using the Arduino IDE for an easy-to-run Internet of Things core. We wired up a high-quality SiLabs CP2104 USB-Serial chip that can upload code at a blistering 921600 baud for fast development time. It also has auto-reset so no noodling with pins and reset button pressings. The CP2104 has better driver support than the CH340 and can do very high speeds without stability issues.

To make it easy to use for portable projects, we added a connector for any of our 3.7V Lithium polymer batteries and built in battery charging. You don't need a battery, it will run just fine straight from the micro USB connector. But, if you do have a battery, you can take it on the go, then plug in the USB to recharge. The Feather will automatically switch over to USB power when its available.

Here's some handy specs!

  • Measures 2.0" x 0.9" x 0.28" (51mm x 23mm x 8mm) without headers soldered in
  • Light as a (large?) feather - 9.7 grams
  • ESP-F V1.1 @ 80MHz with 3.3V logic/power
  • 4MB of FLASH (32 MBit)
  • Built in WiFi 802.11 b/g/n
  • 3.3V regulator with 500mA peak current output
  • CP2104 USB-Serial converter onboard with 921600 max baudrate for speedy uploading
  • Auto-reset support for getting into bootload mode before firmware upload
  • 9 x GPIO pins - can also be used as I2C and SPI
  • 1 x analog inputs 1.0V max
  • Built in 100mA LiPoly charger with charging status indicator LED, can also cut a trace to disable the charger
  • Pin #0 red LED for general purpose blinking. Pin #2 blue LED for bootloading debug & general purpose blinking
  • Power/enable pin
  • 4 mounting holes
  • Reset button

Comes fully assembled and tested, with a USB interface that lets you quickly use it with the Arduino IDE or NodeMCU Lua (it comes preprogrammed with the Lua interpreter). We also toss in some headers so you can solder it in and plug into a solderless breadboard. Lipoly battery and USB cable not included

Check out our tutorial for all sorts of details, including schematics, files, IDE instructions, power management and more!Check out our tutorial for all sorts of details, including schematics, files, IDE instructions, power management and more!

Technical Details

23mm x 51mm x 7.2mm / 0.9" x 2" x 0.28"
Weight: 6.2
Datasheets, schematic, EagleCAD PCB files, and Fritzing available in the product tutorial
RoHS

 

Distributeur Suisse de

Expédition

Envoi Suisse
Suisse
Swiss shipping
 
Envoi international
terre001
International shipping

ZigoBot à Lausanne

Horaires de la boutique : 

du Mardi au Vendredi de 10h à 18h
et le Samedi de 10h à 14h.

Rue de la Grotte 4 (sous la place Saint-François) • 1003 Lausanne

 

Newsletter